Conductive adhesive coating on the Cu mesh or Al mesh machine

Update: 2016-04-29      View:7799
  • Item Num :TOB-CUMESH-COAT300
  • Shipping Port: XIAMEN
  • MOQ :1set
  • Payment :L/C,T/T,Western Union, Paypal
  • Product Orgin:China
  • Delivery Time :90days
  • Order Online
Message

have a question? you can call us or Email us by sending a message below.

Subject : Conductive adhesive coating on the Cu mesh or Al mesh machine

Introduction

Conductive adhesive coating on the Cu mesh or Al mesh machine

SPECIFICATIONS

 1, Equipment standard composition and key configuration table

1)   Put roll mechanism;

2)   Coating tension mechanism;

3)   Coating mechanism;

4)   Drying system;

5)   Winding tension mechanism;

6)   Winding mechanism;

7)   Automatic control system.

 2,Machine Picture


 3,Machine Charactor

No

Item

Charactor

Remark

1

Size

Width

1.5m

Place Area : 2m(W)*10m(L)*5m(H)

Length

8m

Height

5m

2

Coating type

Continuous coating

 

3

Scraper adjustment mode

Servo motor control

 

4

Effective coating width

≤300mm

 

5

Coating speed

1-12m/min

Coating speed is related to the material system and coating thickness.

6

Coating speed precision error

≤0.1m/min

 

7

Coating speed

15m/min

 

8

Overall length of coating machine

≤12m

Front of machine:3.5 meters,

End of machine: 3.5 meters.

9

Overall height of coating machine

≤5M

 

10

Oven length

3m

Motor drive roller transmission

11

Single section oven heating power

13.5Kw

Electric heating

12

Oven maximum temperature

150

Ambient temperature of 30 degrees, single section measurement

13

Oven surface temperature

≤50

 

14

Temperature control precision

±1

Indicator value difference of temperature control meter

15

Single oven section wind quantity

2500m^3/h~3500^3/h

Up and down get in a draught, frequency conversion control, air volume can be adjusted

16

Coating thickness error

±1.5μm

 

17

Winding error of edge order

±0.5 mm

Φ400mm/Roll

18

Rectification method (including the outlet of the oven Rectification)

Automatic deviation correction, precision ±0.5 mm

Ultrasonic testing / servo motor

19

Unwinding mechanism

Speed control mode of variable frequency motor

Maximum load weight 200kg.

20

Winding mechanism

Servo motor

21

Tension control system

Constant tension

Automatic tension compensation,

Partial tension control of the Winding / unwinding

22

Controller and man machine interface

10.2 Inch color touch screen

Convenient operation and maintenance

23

Equipment main body color

Light gray powder (except stainless steel) 

Standard color PANTONE 1C (Have special requirements, please provide the color) 

24

Oven transition roller

Surface polishing / oxidation treatment

Stainless steel non grease rolling bearing

25

Oven insulation material, oven material, thickness, sealing

Oven material is SUS304/ 202 stainless steel, thickness 1.5mm, NMP corrosion protect. With the continuous weld liner, leak proof NMP.

Insulation material for rock wool insulation oven, effective for temperature keep.

26

Abnormal alarm function

Buzzer / touch screen prompt failure reason

 

27

Safety device

Mechanical interlock / safety warning signs / emergency stop switch button / protective cover, etc.

 

28

Counting function

Production quantity / length

 

4,Environmental requirements:

     1), Temperature: Front part  27±3;

     2), Relative humidity: Front part : ≤30 HR%;

     3),Compressed air: after drying, filtration and pressure regulator: air pressure: ≥5.0kg/cm2; Gas consumption is about 4m3/h

     4), Power: three-phase 380V, 50HZ, voltage fluctuation range: +10% ~ -10%; equipment maximum power 25KW; (Normal working is about 60% of the maximum power)

     5), Ground: protection of grounding.

     6), Ground requirements: the basis for cement and terrazzo floor, flatness ±2mm/, the carrying capacity of 600/;

     7), Party A is responsible for to party a site from the coating machine installation of the nearest location required by Party B design of electric power, gas and the, requirements per device is provided with independent air supply switch and gas source interface, and Party A shall confirm the equipment display layout.

     8), Coating machine outside the air inlet and exhaust pipes, valves, exhaust fan by Party A to provide;

       9), The equipment in the first party to use the power of debugging, the substrate, the size of party a free of charge, and is responsible for the arrangement of the relevant operating personnel, maintenance personnel and technical personnel;

PACKAGE AND SHIPPING

1 Standard exported package : Internal anticollision protection, external export wooden box package

2 Shipping by express, by air, by sea according to customer's requirements to suggest the most suitable shipping mode

3 Responsible for the damage during shipping process, change the damage part for free

4 Supply with suitable voltage input and power plug according to customer's country requirements.

5 Supply with CO, ECO, FORM A, FORM E and any other original certificate for import custom clearance and tax relief.

SERVICES

1 We supply machines with battery technology support.

2 We can also supply a full set of materials for lithium battery including polymer battery, cylinder battery, mobile phone battery, EV battery.

3 We can also supply a full set of lithium battery equipment for lab research, pilot scale research and production line.

4 We can also supply a full set of battery technology for battery design, research and producing.

We cooperated with each other, and we will do TOP OF THE BEST battery

Related Tags : Cu mesh     Al mesh     coating machine    
Related Product